Construction Calculators

Jump to a tool or explore below.

Free CMU Calculator

Concrete Block Calculator

Count the concrete blocks for any wall, with doors and windows deducted, then get mortar bags, grouted cores, grout volume and vertical rebar for 4- to 12-inch CMU.

Block count by course
Mortar and grout
Rebar and cost

Concrete Block Calculator

Enter the wall, block size and openings; add grouted cores to get grout and vertical rebar

Calculator inputs

Total area of openings to deduct from all walls.

Quikrete Mortar Mix data sheet: up to 13 standard 8×8×16 blocks per 80 lb bag. Use your product's figure.

Planning estimate only. Confirm field measurements, product coverage, local requirements, waste, pricing, and supplier quantities before ordering or bidding.

Block Formula and Worked Example

Blocks = round up(length ÷ 16 in) × round up(height ÷ 8 in) × walls
Quick check: wall area (sq ft) × 1.125 blocks per sq ft

The 16 × 8 inch module is the actual block (15-5/8 × 7-5/8 in) plus one 3/8-inch mortar joint, as described in the CMHA guide to modular concrete masonry. Each module covers 128 square inches, or 0.889 square feet, which gives 1.125 blocks per square foot.

Example: a 20 ft × 8 ft wall of 8 × 8 × 16 block

  1. Blocks per course: 240 in ÷ 16 in = 15; courses: 96 in ÷ 8 in = 12
  2. Blocks: 15 × 12 = 180 (160 sq ft × 1.125 agrees)
  3. With 10% waste: 180 × 1.10 = 198 blocks
  4. Mortar at 13 blocks per 80 lb bag: 198 ÷ 13 = 15.2, so 16 bags
  5. Cores grouted every 48 in: 6 cell lines × 12 courses = 72 cells, about 8.3 cu ft of grout before waste
  6. Vertical rebar: 6 lines × 8 ft = 48 linear ft before laps and dowels

CMU Sizes

Nominal sizes are width × height × length in inches and include a 3/8-inch joint. Width changes the grout, rebar and price of the wall, but every unit with an 8 × 16 face lays at the same 1.125 blocks per square foot.

Nominal size (in)Actual size (in)Blocks per sq ftTypical use
4 × 8 × 163-5/8 × 7-5/8 × 15-5/81.125Veneer, partitions, screen walls
6 × 8 × 165-5/8 × 7-5/8 × 15-5/81.125Interior and non-load-bearing walls
8 × 8 × 167-5/8 × 7-5/8 × 15-5/81.125Standard structural and foundation walls
8 × 4 × 167-5/8 × 3-5/8 × 15-5/82.25Half-high courses to make up height
10 × 8 × 169-5/8 × 7-5/8 × 15-5/81.125Taller or more heavily loaded walls
12 × 8 × 1611-5/8 × 7-5/8 × 15-5/81.125Foundation and basement walls

Mortar, Grout and Rebar

Mortar. The Quikrete Mortar Mix data sheet says an 80 lb bag lays up to 13 standard 8 × 8 × 16 blocks or 37 standard bricks. That is the calculator's default; enter your own product's figure, and use fewer blocks per bag for half-high units, which have more joint per block.

Grout. Quikrete's bulk masonry mortar and grout data sheet says a 3,000 lb bag yields 0.90 cubic yards of coarse grout and fills the cores of about 105 standard 8 × 8 × 16 blocks. That works out to about 0.23 cubic feet per fully grouted block, or 0.115 per cell, the calculator's default. Wider units hold more grout, so enter the void volume your block maker publishes.

Rebar. Vertical bars sit in the grouted cells, one per grouted cell line, at the spacing on the drawings. The calculator gives that length before laps, dowels into the footing, bond beams and lintels, which you take off from the structural drawings.

Grout for a 10 ft × 8 ft wall by core spacing

Grouted coresCellsGrout (cu ft)Grout (yd³)
Every 48 in364.10.15
Every 32 in485.50.20
Every 24 in728.30.31
Every 16 in9611.00.41
Solid grouted19222.10.82

8 × 8 × 16 block, 12 courses, 0.23 cu ft per fully grouted block, before waste.

Automate your masonry takeoffs and quotes.

Get more masonry quotes out with less manual measuring and data entry. BuildVision extracts wall and opening measurements from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.

How the Concrete Block Calculator Works

Every block with an 8 × 16 inch face, whatever its width, covers 0.889 square feet of wall once the 3/8-inch mortar joint is included, so a wall takes 1.125 blocks per square foot. This calculator does the count the way a mason lays it: whole blocks per course along the length, whole courses up the height, times the number of equal walls, less the whole blocks that fall inside doors and windows.

The block count then drives the rest of the order. Mortar is estimated from the blocks laid per 80 lb bag; Quikrete’s Mortar Mix data sheet gives up to 13 standard 8 × 8 × 16 blocks per bag, and you can enter your own product’s figure. Grout is figured for the cores you fill, at a spacing such as every 48 inches or solid, using about 0.23 cubic feet per fully grouted standard block unless you enter your block maker’s void volume. Grouted cell lines also give the length of vertical rebar, one full-height bar per line.

Width changes the grout, rebar and price, not the count. Choose 4, 6, 8, 10 or 12-inch units, or the 8 × 4 × 16 half-high block, which takes twice as many units per square foot.

Block, mortar and grout formulas

  • Module = actual block dimension + mortar joint (15-5/8 + 3/8 = 16 in long, 7-5/8 + 3/8 = 8 in high)
  • Blocks per course = round up(wall length ÷ module length); courses = round up(wall height ÷ module height)
  • Blocks = blocks per course × courses × walls − whole blocks inside openings
  • Order = round up(blocks × (1 + waste %)); mortar bags = round up(order ÷ blocks per bag)
  • Grouted cells at spacing s = (round down(wall length ÷ s) + 1) × courses
  • Grout (ft³) = grouted cells × grout per block ÷ 2; solid grouting = blocks × grout per block

Estimating Steps and Checks

1

Measure each wall

Measure length and height in feet (meters in metric). Walls of the same size can be entered once with a count; walls of different sizes need separate runs.

2

Pick the block and joint

Choose the nominal block size and enter the mortar joint, normally 3/8 inch. The calculator rounds blocks per course and courses up separately, so a wall that does not fit the 8-inch module shows its cut course.

3

Deduct openings

Enter the total area of doors and windows. Only whole blocks inside the openings come out of the count; cut blocks at jambs and lintels stay in.

4

Set waste and mortar yield

Add an allowance for cuts and breakage from the layout and your job history. Keep 13 blocks per 80 lb bag for Quikrete Mortar Mix or enter your product’s figure.

5

Add grout and rebar

Choose the grouted-core spacing from the structural drawings, or solid grouting, and enter the block maker’s void volume if you have it. Read the grout volume, grouted cells and vertical rebar length, and add bond beams and lintels separately.

Common Checks

  • Height should divide by 8 inches. A 6 ft 8 in wall is exactly 10 courses; a 7 ft wall means a cut or saw-cut top course, which raises both waste and labor.
  • Do not swap premixed mortar for masonry cement. Masonry cement needs sand added and has a different yield per bag.
  • The 0.23 ft³ grout default is derived from Quikrete’s bulk grout data sheet (0.90 yd³ of coarse grout fills about 105 standard blocks). Units from other makers, and 12-inch block, hold different amounts, so use their published void volume.
  • Bond beams, lintels, horizontal joint reinforcement, dowels and lap splices come from the structural drawings and are not in the vertical rebar figure.

Concrete Block Calculator FAQs

How many concrete blocks do I need per square foot of wall?

1.125 for any block with a nominal 8 × 16 inch face, including 4, 6, 8, 10 and 12-inch wide units. Half-high 8 × 4 × 16 blocks take 2.25 per square foot. A 300 square foot wall needs about 338 standard blocks before waste.

How many cinder blocks do I need for a 40-foot wall?

It depends on the height. A 40 ft wall is 30 blocks per course (480 in ÷ 16 in). At 4 ft (6 courses) that is 180 blocks, and at 8 ft (12 courses) it is 360 blocks, before waste and openings.

How many blocks does a bag of mortar lay?

Quikrete’s Mortar Mix data sheet says an 80 lb bag lays up to 13 standard 8 × 8 × 16 blocks, so 100 blocks take about 8 bags. Actual yield depends on the joint profile, bedding and waste. Check the data sheet for the product you buy.

How much grout does it take to fill block cores?

Quikrete’s bulk grout data sheet says a 3,000 lb bag yields 0.90 cubic yards of coarse grout and fills about 105 standard 8 × 8 × 16 blocks, which works out to about 0.23 cubic feet per block. A solid-grouted 20 × 8 ft wall of 180 blocks needs about 41 cubic feet, or 1.53 cubic yards, before waste.

How much rebar goes in a block wall?

Vertical bars go in the grouted cells at the spacing on the drawings, commonly 16 to 48 inches. Count the grouted cell lines along the wall, add one, and multiply by the wall height. A 20 ft wall grouted every 48 inches has 6 lines; at 8 ft tall that is 48 linear feet before laps and dowels.

What are the actual dimensions of an 8x8x16 block?

About 7-5/8 × 7-5/8 × 15-5/8 inches. Nominal sizes include a 3/8-inch mortar joint, so the block plus one joint makes the 8 × 16 inch module used for wall layout.

Is a cinder block the same as a concrete block?

Today, practically yes. “Cinder block” dates from when units were made with coal cinders as aggregate. What suppliers sell now is a concrete masonry unit (CMU), and the counting math is the same whichever name is on the order.

Should I deduct windows and doors from a block count?

Yes, but only the whole blocks that fall inside the opening. Blocks cut around jambs, sills and lintels are still bought. The calculator deducts whole blocks from the opening area you enter and leaves the cuts in.

Try it on your own plans

Automate your masonry takeoffs and quotes.

Get more masonry quotes out with less manual measuring and data entry. BuildVision extracts wall and opening measurements from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.

First takeoff free · No card · $299/seat/month after

Concrete Block Calculator | CMU, Mortar, Grout & Rebar