Construction Calculators
Jump to a tool or explore below.
Rebar Calculator
Lay out rebar for a slab or footing: bars each way, lap splices, total length, stock bars to buy, weight for #3 to #8 bar, and cost.
Rebar Quantity, Weight & Cost Calculator
Choose slab grid or continuous footing, then bar size, spacing, cover and lap
Rebar Formula and Worked Examples
Example 1: 20 × 20 ft slab, #4 at 12 in each way
- Runs inside 3 in of cover: 20 − 0.5 = 19.5 ft each way
- Bars each way: 19.5 ÷ 1 = 19.5, round up to 20 spaces, plus 1 = 21 bars
- Total length: 42 bars × 19.5 ft = 819 ft; no laps, because each bar is shorter than 20 ft
- Weight: 819 × 0.668 lb/ft = 547 lb
- Stock bars: 819 ÷ 20 = 40.95, so 41 bars of 20 ft before waste
Example 2: 40 × 10 ft slab, laps on the long bars
- The 39.5 ft lengthwise runs are longer than a 20 ft bar, so each is made of pieces that overlap
- Lap at 40 bar diameters: 40 × 0.5 in = 20 in for #4
- Pieces per run: (39.5 − 1.67) ÷ (20 − 1.67) = 2.06, so 3 pieces and 2 laps
- 11 lengthwise bars × 2 laps = 22 lap splices, adding 36.7 ft of bar
Automate your concrete takeoffs and quotes.
Spend less time counting bars and laps by hand. Get more concrete quotes out from the drawings you already have. BuildVision extracts slab, footing, and wall measurements from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.
Rebar Sizes and Weight per Foot
Nominal diameters and weights from ASTM A615/A615M, the standard for deformed carbon-steel reinforcing bars. The bar number is the diameter in eighths of an inch; the metric designation is the diameter rounded to whole millimeters.
| Bar size | Metric size | Diameter | lb per ft | kg per m | 20 ft bar (lb) | Lap at 40 d |
|---|---|---|---|---|---|---|
| #3 | #10 | 0.375 in (9.5 mm) | 0.376 | 0.560 | 7.52 | 15 in |
| #4 | #13 | 0.500 in (12.7 mm) | 0.668 | 0.994 | 13.36 | 20 in |
| #5 | #16 | 0.625 in (15.9 mm) | 1.043 | 1.552 | 20.86 | 25 in |
| #6 | #19 | 0.750 in (19.1 mm) | 1.502 | 2.235 | 30.04 | 30 in |
| #7 | #22 | 0.875 in (22.2 mm) | 2.044 | 3.042 | 40.88 | 35 in |
| #8 | #25 | 1.000 in (25.4 mm) | 2.670 | 3.973 | 53.40 | 40 in |
The 40-diameter lap is a planning value only. Required lap lengths depend on bar size, concrete strength, cover, spacing and bar position; take them from the drawings or ACI 318.
How to Measure for Rebar
Slabs
Measure the slab inside the forms. Bars running the length of the slab are spaced across its width, and the other way round, so enter both spacings. Thickened edges and extra bars at openings are separate items.
Continuous footings
Enter the total footing length around the building and the footing width. Set the number of long bars from the drawings, and a cross-bar spacing if there are short bars across the footing, or 0 if not.
Edge cover
Cover is the concrete between the bar and the outside face. The calculator trims it from both ends of every bar. ACI 318 gives minimum cover by exposure; 3 inches is the usual figure for concrete cast against earth.
Stock length and waste
Rebar is commonly sold in 20 ft lengths, and longer lengths are available from steel suppliers. Waste covers cut-offs that cannot be reused; a cutting list on big jobs shows the real figure.
How the Rebar Calculator Works
A rebar takeoff answers four questions: how many bars run each way, how long they are, how many stock bars you have to buy once laps are added, and what the steel weighs. This calculator works through all four for a slab grid or a continuous footing, in feet and inches or meters and centimeters.
Bars stop short of the forms by the edge cover you enter, typically 3 inches against earth-formed edges, so a 20 ft slab has 19.5 ft runs. The number of bars in each direction is the run divided by the spacing, rounded up, plus one, which keeps the spacing at or under what you entered. Runs longer than one stock bar are made from overlapping pieces, and each joint adds a lap splice; the default lap of 40 bar diameters is a common planning value, and the drawings or ACI 318 set the real length.
Weight uses the nominal weights in ASTM A615 for #3 to #8 bars: 0.376, 0.668, 1.043, 1.502, 2.044 and 2.670 lb per foot. Enter a price per stock bar to cost the order. Chairs, ties, dowels and bent bars are separate takeoff items.
Rebar layout and weight formulas
- Run = dimension − 2 × edge cover
- Bars across a run = round up(run ÷ spacing) + 1
- Lap length = lap in bar diameters × bar diameter (a #4 bar is 0.5 in, so 40 diameters = 20 in)
- Pieces per bar line = round up((run − lap) ÷ (stock length − lap)) when the run is longer than one stock bar
- Total length = bars × run + lap splices × lap length; order length = total × (1 + waste %)
- Weight = order length × nominal weight (lb/ft); stock bars = round up(order length ÷ stock length)
Estimating Steps and Checks
Choose slab or footing
A slab grid has bars in both directions at set spacings. A continuous footing has a set number of long bars, with optional short cross bars at a spacing.
Enter the dimensions and edge cover
Enter the slab or footing length and width, and the clear cover from the form to the end of the bar. The calculator subtracts the cover from both ends of every run.
Set bar size and spacing
Pick the bar size from the drawings and enter the spacing for bars running lengthwise and widthwise. Spacing is measured center to center.
Enter stock length and lap
Enter the stock bar length you buy, usually 20 ft, and the lap splice in bar diameters. The calculator adds a lap at each joint on runs longer than one bar.
Add waste and price
Add an allowance for cut-offs and errors, then the price per stock bar. Read the stock bars to buy, total weight and cost, and confirm with the drawings and your supplier.
Common Checks
- Weight check: a 20 ft #4 bar weighs 13.4 lb and a 20 ft #5 bar weighs 20.9 lb at the ASTM A615 nominal weights.
- Lap splices add up. On a 40 ft slab with 20 ft stock, every lengthwise line needs three pieces and two laps; at 40 diameters a #4 lap is 20 inches.
- Stock bars here are total length divided by stock length. Cut-offs that cannot be reused can need more bars, so check a cutting list on large jobs.
- This is a quantity takeoff, not a design. Bar size, spacing, cover and laps come from the structural drawings, ACI 318 or the local code.
Rebar Calculator FAQs
How much rebar do I need for a 20x20 slab?
At 12 inches on center each way with 3 inches of edge cover, the runs are 19.5 ft and there are 21 bars each way: 42 bars, 819 linear feet, about 547 lb of #4 bar. That is 41 stock bars of 20 ft before waste, with no laps needed because each run is shorter than a stock bar.
How much does rebar weigh per foot?
ASTM A615 nominal weights are 0.376 lb/ft for #3, 0.668 for #4, 1.043 for #5, 1.502 for #6, 2.044 for #7 and 2.670 for #8. In metric that is about 0.56, 0.99, 1.55, 2.24, 3.04 and 3.97 kg per meter.
What do rebar sizes like #4 mean?
The number is the nominal diameter in eighths of an inch. A #4 bar is 4/8 or 1/2 inch, a #5 is 5/8 inch and a #8 is 1 inch. The calculator uses that diameter for the lap length.
How long should a rebar lap splice be?
It depends on the bar size, concrete strength, cover, spacing and position, and the drawings or ACI 318 set it. Forty bar diameters is a common planning value, which is 20 inches for a #4 bar and 25 inches for a #5. Enter the length your drawings call for.
How do I calculate rebar spacing?
Subtract the edge cover from both ends of the span, divide by the spacing, round up and add one. A 19.5 ft run at 12 inches is 19.5 bars, rounded up to 20 spaces and 21 bars. Rounding up keeps the actual spacing at or under the spacing you specified.
How many pieces of rebar come in a ton?
Divide 2,000 lb by the weight of one bar. A 20 ft #4 bar weighs 13.36 lb, so a short ton is about 150 bars. A 20 ft #5 bar weighs 20.86 lb, about 96 bars per ton.
How much rebar goes in a footing?
A continuous footing usually has two or more long bars along its length, sometimes with short cross bars. Choose "Continuous footing", enter the number of long bars and the cross-bar spacing (0 for none), and the calculator adds laps on runs longer than a stock bar.
Estimating Software by Trade
Related Tools & Resources
Turn Calculator Work Into Bids
Estimating Software
Related Calculators
Software Comparisons
Try it on your own plans
Automate your concrete takeoffs and quotes.
Spend less time counting bars and laps by hand. Get more concrete quotes out from the drawings you already have. BuildVision extracts slab, footing, and wall measurements from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.
First takeoff free · No card · $299/seat/month after