Construction Calculators
Jump to a tool or explore below.
Sand Calculator
Enter the area and depth to get cubic yards, tons and 0.5 cu ft bags of sand, for dry, damp or wet sand.
Sand Volume, Tons & Bags
Choose the sand condition to fill in its density. Moisture changes the weight, not the volume.
Worked example: 1 inch of bedding sand under a 12 x 12 ft patio
Damp sand at the published 100 lb/ft³ (1.35 short tons per cubic yard), with a 10% allowance. These are the calculator defaults.
- 1Area = 12 ft x 12 ft = 144 sq ft
- 2Volume = 144 sq ft x (1 in / 12) = 12 cu ft
- 3Cubic yards = 12 / 27 = 0.44 yd³
- 4Order volume = 12 x 1.10 = 13.2 cu ft = 0.49 yd³
- 5Weight = 13.2 cu ft x 100 lb = 1,320 lb = 0.66 short tons
- 6Bags = 13.2 / 0.5 cu ft = 26.4, so 27 bags
Sand weight per cubic yard
These are the densities the material picker fills in. Each comes from the published row named in the last column. Moisture, gradation and how the material was loaded change real weight, so use your supplier's weight per yard when you have it.
| Material | lb per cubic yard | Short tons per yd³ | Tonnes per m³ | Typical uses | Published row |
|---|---|---|---|---|---|
| Sand, dry | 2,619 | 1.31 | 1.55 | Paver bedding, play sand, mortar and masonry sand bought dry | Sand, dry: 97 lb/ft³ |
| Sand, damp | 2,700 | 1.35 | 1.60 | Typical stockpiled sand with some moisture | Sand, damp: 100 lb/ft³ |
| Sand, wet | 3,213 | 1.61 | 1.91 | Fill and bedding sand delivered wet | Sand, wet: 119 lb/ft³ |
| Sand, wet and packed | 3,510 | 1.76 | 2.08 | In-place compacted wet sand (not a loose delivery figure) | Sand, wet, packed: 130 lb/ft³ |
Source: Engineering ToolBox, Dirt and Mud - Densities; Engineering ToolBox, Densities of Common Products. Where the source gives a range, the default is its midpoint. Short tons per cubic yard = lb/ft³ x 27 / 2,000.
Sand depth by use
The depth presets in the calculator, and how far one cubic yard goes at each depth. Use the depth in your plan or specification when there is one.
| Depth | Common use | 1 yd³ covers | Yards per 100 sq ft |
|---|---|---|---|
| 1 in (2.5 cm) | paver bedding | 324 sq ft | 0.31 yd³ |
| 2 in (5.1 cm) | leveling layer | 162 sq ft | 0.62 yd³ |
| 4 in (10.2 cm) | under slab or pool | 81 sq ft | 1.23 yd³ |
| 6 in (15.2 cm) | fill | 54 sq ft | 1.85 yd³ |
| 12 in (30.5 cm) | sandbox, deep fill | 27 sq ft | 3.70 yd³ |
Automate your sitework takeoffs and quotes.
Get more sitework quotes out with less time measuring plans and moving quantities into a price sheet. BuildVision extracts site areas and measurements from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.
How the Sand Calculator Works
Sand is measured by volume and usually sold by the ton, and its weight changes a lot with moisture. This calculator turns area and depth into cubic yards, then into tons using the moisture condition you choose, and also gives the count of 0.5 cu ft bags.
A 12 x 12 ft paver patio with a 1 inch bedding layer needs 12 cubic feet of sand, or 0.44 cubic yards. At the density for damp sand (100 lb/ft³) that is 1,200 lb, or 0.6 short tons. With a 10 percent allowance it is 0.66 tons or 27 bags of 0.5 cu ft.
Densities come from Engineering ToolBox: dry sand 97 lb/ft³, damp sand 100, wet sand 119, and wet packed sand 130. That is 1.31 to 1.76 short tons per cubic yard. Use the supplier's weight per yard when you have it.
Sand volume and weight formulas
- Cubic feet = length (ft) x width (ft) x depth (in) / 12
- Cubic yards = cubic feet / 27
- Order cubic yards = cubic yards x (1 + allowance % / 100)
- Short tons = order cubic yards x bulk density (short tons per yd³)
- Bags = order cubic feet / bag size (cu ft), rounded up
Estimating Steps and Checks
Measure the area
Measure length and width in feet. Use Circle for round sandboxes or pool bases, and Known area if you already have the square footage from a plan.
Choose the depth
Use the depth from the paver, slab or pool installer's instructions. The presets cover common cases: 1 inch for paver bedding, 2 inches for a leveling layer, 4 to 6 inches for a base or fill, 12 inches for a sandbox.
Choose dry, damp or wet sand
Stockpiled sand is usually damp. Pick the condition that matches what will be delivered, or type the supplier's density. This only changes the weight; the volume stays the same.
Read the order and round up
Read cubic yards, tons and bags, then round up to the supplier's minimum or to whole bags. Enter a price per ton to see the cost.
Common Checks
- Moisture adds weight, not volume. The same cubic yard of sand is about 2,619 lb dry and 3,213 lb wet at the published densities.
- One cubic yard covers 324 sq ft at 1 inch and 162 sq ft at 2 inches.
- For pavers, bedding sand is screeded to an even layer over a compacted base. The base is gravel, not sand; size it with the gravel calculator.
- Packed sand (130 lb/ft³) describes sand compacted in place, not a loose delivery. Use it only to estimate the weight of sand already in place.
Sand Calculator FAQs
How much sand do I need?
Multiply length x width in feet by depth in inches, divide by 12 for cubic feet and by 27 for cubic yards. A 12 x 12 ft patio at 1 inch needs 144 / 12 = 12 cubic feet, or 0.44 cubic yards.
How many tons of sand are in a cubic yard?
About 1.3 to 1.6 short tons for loose sand. Engineering ToolBox lists dry sand at 97 lb/ft³ (2,619 lb per cubic yard, 1.31 tons), damp sand at 100 lb/ft³ (2,700 lb, 1.35 tons) and wet sand at 119 lb/ft³ (3,213 lb, 1.61 tons).
How many bags of sand are in a cubic yard?
54 bags of 0.5 cu ft, since a cubic yard is 27 cubic feet. If your bags are labeled by weight, a 50 lb bag of dry sand at 97 lb/ft³ is about 0.52 cubic feet, so a cubic yard is about 52 of those bags.
How much sand do I need for pavers?
Pavers usually sit on a thin bedding layer, often about 1 inch, over a compacted gravel base; follow the paver manufacturer's instructions. At 1 inch, each 100 sq ft needs 8.3 cubic feet of sand. Joint sand swept between pavers is a separate, smaller quantity.
How much area does a ton of sand cover?
At 100 lb/ft³ (damp sand), one short ton is 20 cubic feet. That covers 240 sq ft at 1 inch, 120 sq ft at 2 inches or 60 sq ft at 4 inches.
How much sand for a sandbox?
A 6 x 6 ft sandbox filled 12 inches deep needs 36 cubic feet, or 1.33 cubic yards. At 97 lb/ft³ dry, that is about 3,500 lb, or 72 bags of 0.5 cu ft.
Should I buy sand by the ton or by the yard?
Use whichever the supplier prices by, but calculate in both. If they sell by the ton, ask whether the sand is dry or wet, because wet sand weighs more for the same volume and you get less volume per ton.
Estimating Software by Trade
Related Tools & Resources
Turn Calculator Work Into Bids
Estimating Software
Try it on your own plans
Automate your sitework takeoffs and quotes.
Get more sitework quotes out with less time measuring plans and moving quantities into a price sheet. BuildVision extracts site areas and measurements from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.
First takeoff free · No card · $299/seat/month after