Construction Calculators

Jump to a tool or explore below.

Free Stair Stringer Calculator

Stair Stringer Calculator

Lay out a cut stringer: riser and tread size, framing square setting, layout marks, stringer and board length, throat depth, bottom drop, and how many stringers the stair needs.

Layout Marks
Board Length
Stringer Count

Stair Stringer Layout Calculator

Enter total rise, tread depth, and stair width to lay out the stringer cuts.

Calculator inputs

Finished floor or grade to finished landing.

Overrides the target riser height.

Dropped off the bottom of the stringer so the first riser matches the rest.

Set from the tread material's span and local requirements.

A 2x12 is 11-1/4 in actual.

Planning estimate only. Confirm field measurements, product coverage, local requirements, waste, pricing, and supplier quantities before ordering or bidding.

Worked Example: Stringers for a 105 Inch Rise

A deck sits 105 in above the landing pad. The stair is 36 in wide with 10-1/2 in treads made of two 1 in thick deck boards, cut from 2x12 stringers.

StepMathResult
Risers and riser height105 / 7.5 = 14; 105 / 1414 risers of 7-1/2 in
Notches per stringer14 - 113
Framing squarerise on tongue, tread on blade7-1/2 in and 10-1/2 in
Step diagonal (mark spacing)square root (7.5² + 10.5²)12-7/8 in
Layout linesquare root (105² + 136.5²)14 ft 4-3/16 in
Minimum boardlayout line + one step diagonal15 ft 5-1/8 in, buy 16 ft
Throat left in a 2x1211.25 - (7.5 x 10.5 / 12.90)about 5-1/8 in
Bottom dropone tread thickness1 in
Stringersround up (36 / 16) + 14

Throat Depth Left by Common Step Sizes

Solid wood left below the notches, measured square to the bottom edge. A deeper notch or a narrower board leaves less.

Riser x treadStep diagonal2x12 (11-1/4 in)2x10 (9-1/4 in)
7 x 11 in13.04 in5.34 in3.34 in
7.25 x 10.5 in12.76 in5.28 in3.28 in
7.5 x 10 in12.50 in5.25 in3.25 in
7.5 x 10.5 in12.90 in5.15 in3.15 in
7.75 x 10 in12.65 in5.12 in3.12 in

Number of Stringers by Stair Width

Stringers = width divided by the maximum spacing, rounded up, plus one. The spacing your treads allow depends on the tread material and thickness.

Stair width12 in max spacing16 in max spacing18 in max spacing
36 in443
42 in544
48 in544
60 in655

Plan the whole stair first, including headroom and the 2021 IRC riser and tread limits, with the stair calculator.

Automate your stair takeoffs and quotes.

Spend less time moving stair quantities into price sheets. Get the next quote moving from your drawings and specifications. BuildVision extracts stair counts and measurements from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.

How the Stair Stringer Calculator Works

A cut stringer is a sawtooth: one notch per tread, each notch a right triangle with the riser height on one leg and the tread depth on the other. Lay it out by setting a framing square to the riser height on the tongue and the tread depth on the blade, then stepping the square up the board once per tread. The diagonal of that triangle is the spacing between layout marks along the edge of the board.

This calculator turns the total rise and your tread depth into everything you need at the saw: riser count and height, the framing square setting, each layout mark measured from the bottom, the stringer length, the board length to buy, the wood left below the notches (the throat), how much to drop the bottom for tread thickness, and how many stringers the stair width needs. It also flags the riser and tread against the 2021 IRC limits.

Stair stringer formulas

  • Risers = round up (total rise / target riser); riser height = total rise / risers
  • Treads (notches per stringer) = risers - 1
  • Step diagonal = square root (riser squared + tread squared)
  • Layout line = square root (total rise squared + (tread x treads) squared)
  • Minimum board length = layout line + one step diagonal
  • Throat depth = board width - (riser x tread / step diagonal)
  • Stringers = round up (stair width / max spacing) + 1

Estimating Steps and Checks

1

Measure the total rise

Measure plumb from the landing surface (finished floor, slab, or pad) to the top of the deck or upper floor. On sloped ground, measure where the bottom of the stair will land, not at the house.

2

Set riser, tread, and tread thickness

Enter a target riser (7 to 7-1/2 in is common) and a tread depth (10-1/2 in suits two 2x6 deck boards with a gap). Enter the tread thickness; the bottom of the stringer is cut down by that much so the first riser comes out the same as the others after the treads go on.

3

Lay out with a framing square

Clamp stair gauges to the square at the riser height on the tongue and the tread depth on the blade. Start at the bottom, trace the first notch, and slide the square to the next mark. The layout marks in the results let you check each step with a tape.

4

Check the throat and count stringers

Confirm the wood left below the notches meets your design guide, then cut one stringer, test it in place, and use it as the pattern for the rest. Space stringers no farther apart than your tread material allows.

Common Checks

  • Worked example: a 105 in rise at a 7-1/2 in target gives 14 risers of exactly 7-1/2 in and 13 treads. With 10-1/2 in treads the step diagonal is 12-7/8 in, the total run 136-1/2 in, and the layout line about 14 ft 4-3/16 in. The minimum board is about 15 ft 5-1/8 in, so buy a 16 ft 2x12.
  • Throat: a 2x12 is 11-1/4 in wide. Cutting 7-1/2 x 10-1/2 in notches leaves about 5-1/8 in of solid wood below them. Many builders and deck guides look for at least 5 in; if you come up short, use a wider board, a smaller notch, or a different stringer design.
  • Bottom drop: the first riser is cut shorter by one tread thickness, because every other tread adds the same thickness to its step. With 1 in deck boards, take 1 in off the bottom of the stringer.
  • Stringer count: a 36 in wide stair at no more than 16 in between stringers needs round up (36 / 16) + 1 = 4 stringers. Wider spacing may be allowed for thicker treads; confirm with the tread manufacturer and local requirements.
  • Code reference: the 2021 IRC limits risers to 7-3/4 in (R311.7.5.1) and treads to no less than 10 in (R311.7.5.2), with no more than 3/8 in variation within a flight.

Stair Stringer Calculator FAQs

How do I calculate stair stringers?

Measure the total rise, divide by a target riser height, and round up to get the number of risers. Divide the total rise by that number for the exact riser height. Treads are one fewer than risers. The stringer length is the square root of total rise squared plus total run squared, where total run is tread depth times the number of treads.

How long should a stair stringer board be?

Longer than the layout line, because the top plumb cut and bottom level cut extend past it. This calculator adds one step diagonal to the layout line and rounds up to a stock length. For a 105 in rise with 13 treads of 10-1/2 in, the minimum is about 15 ft 5 in, so a 16 ft board.

How many stringers do I need for 36 inch wide stairs?

Divide the width by the maximum stringer spacing, round up, and add one. At 16 in maximum spacing a 36 in stair needs 4 stringers; at 18 in it needs 3. The right spacing depends on the tread material and thickness, so check the tread product and your local requirements.

How do you lay out a stair stringer with a framing square?

Set the riser height on the tongue (the short leg) and the tread depth on the blade (the long leg), ideally with stair gauges. Place the square on the board with both marks on the top edge, trace the notch, slide the square so the blade mark becomes the next tongue mark, and repeat once per tread.

Why do you cut the bottom of a stair stringer shorter?

Each tread adds its thickness on top of the notch. On every step above the first, that thickness is matched by the tread below, but the first step sits on the floor. Cutting the bottom of the stringer down by one tread thickness keeps the first riser equal to the rest.

What size lumber is used for stair stringers?

Cut stringers are usually 2x12, which is 11-1/4 in wide actual. After cutting typical notches, a 2x12 leaves about 5 in of throat; a 2x10 (9-1/4 in) often leaves too little for full-size steps. Pressure-treated lumber is used outdoors.

What is the throat of a stair stringer?

The throat is the narrowest depth of solid wood left below the notches, measured square to the bottom edge of the board. It equals the board width minus riser times tread divided by the step diagonal. It is what carries the load, so a deeper notch or narrower board weakens the stringer.

What riser height and tread depth should a stringer use?

For homes covered by the 2021 IRC, risers may be no taller than 7-3/4 in and treads no shallower than 10 in. Many builders aim for 7 to 7-1/2 in risers and 10-1/2 to 11 in treads for a comfortable stair.

Try it on your own plans

Automate your stair takeoffs and quotes.

Spend less time moving stair quantities into price sheets. Get the next quote moving from your drawings and specifications. BuildVision extracts stair counts and measurements from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.

First takeoff free · No card · $299/seat/month after

Stair Stringer Calculator | Layout, Cuts & Board Length