Construction Calculators

Jump to a tool or explore below.

Free Gravel Calculator

Gravel Calculator

Pick the stone and the depth, enter the area, and get cubic yards, tons, 0.5 cu ft bags, truckloads and cost for a driveway, path, patio base or drain.

Gravel Volume, Tons & Cost

Picking a material fills in its bulk density; picking a depth preset fills in the depth. Both stay editable.

Calculator inputs

Rectangle length, or triangle base.

Rectangle width, or triangle height.

Picking a material fills this in. Replace it with the supplier's figure when you have one.

Extra for settling, compaction, uneven ground and spillage. Set from job history.

Volume printed on the bag.

Ask the hauler. Heavy material can hit the weight limit before the box is full.

Planning estimate only. Confirm field measurements, product coverage, local requirements, waste, pricing, and supplier quantities before ordering or bidding.

Worked example: a 10 x 30 ft driveway at 4 inches

Crushed stone #57 at the published dry gravel density of 105 lb/ft³ (1.42 short tons per cubic yard), with a 10% order allowance. These are the calculator's default inputs.

  1. 1Area = 10 ft x 30 ft = 300 sq ft
  2. 2Volume = 300 sq ft x (4 in / 12) = 100 cu ft
  3. 3Cubic yards = 100 / 27 = 3.70 yd³ (2.83 m³)
  4. 4Order volume = 3.70 x 1.10 = 4.07 yd³ (110 cu ft)
  5. 5Weight = 3.70 yd³ x 1.4175 = 5.25 short tons measured, 5.78 short tons to order
  6. 6Bags = 110 cu ft / 0.5 cu ft = 220 bags
  7. 7Truckloads at 10 yd³ = 4.07 / 10 = 1 load

Gravel density by type

These are the densities the material picker fills in. Each comes from the published row named in the last column. Moisture, gradation and how the material was loaded change real weight, so use your supplier's weight per yard when you have it.

Materiallb per cubic yardShort tons per yd³Tonnes per m³Typical usesPublished row
Crushed stone #572,8351.421.68Driveway top course, drainage stone, slab and footing baseGravel, dry: 105 lb/ft³
Pea gravel2,8351.421.68Walkways, patios, play areas, drainage around pipeGravel, dry: 105 lb/ft³
River rock2,8351.421.68Landscape beds, dry creek beds, bordersGravel, dry: 105 lb/ft³
Crusher run / road base2,9161.461.73Driveway and parking base, compacted sub-base under pavers and slabsSand with gravel, dry: 108 lb/ft³
Decomposed granite2,9161.461.73Paths, patios, xeriscape ground coverSand with gravel, dry: 108 lb/ft³
Gravel, wet3,3751.692.00Use when the stockpile is saturated (washed or rained-on stone)Gravel, wet: 125 lb/ft³

Source: Engineering ToolBox, Dirt and Mud - Densities; Engineering ToolBox, Densities of Common Products. Where the source gives a range, the default is its midpoint. Short tons per cubic yard = lb/ft³ x 27 / 2,000.

How deep should gravel be?

The depth presets in the calculator, and how far one cubic yard goes at each depth. Use the depth in your plan or specification when there is one.

DepthCommon use1 yd³ coversYards per 100 sq ft
2 in (5.1 cm)decorative bed, walkway162 sq ft0.62 yd³
3 in (7.6 cm)path, patio surface108 sq ft0.93 yd³
4 in (10.2 cm)driveway top course81 sq ft1.23 yd³
6 in (15.2 cm)driveway base, drainage54 sq ft1.85 yd³
8 in (20.3 cm)heavy-use base (two lifts)41 sq ft2.47 yd³
12 in (30.5 cm)French drain trench27 sq ft3.70 yd³

Automate your sitework takeoffs and quotes.

Get more sitework quotes out with less time measuring plans and moving quantities into a price sheet. BuildVision extracts site areas and measurements from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.

How the Gravel Calculator Works

Gravel is measured by volume and sold by weight, so a gravel estimate always takes two steps: area times depth gives cubic yards, and cubic yards times the bulk density of the stone gives tons. This calculator does both. Pick the material and it fills in a planning density; pick a depth preset or type your own; then read cubic yards, cubic feet, tons, 0.5 cu ft bags, truckloads and cost from one result.

A 10 x 30 ft driveway at 4 inches deep is 100 cubic feet, or 3.70 cubic yards. At dry gravel density (105 lb/ft³, which is 1.42 short tons per cubic yard) that is 5.25 short tons. Add a 10 percent order allowance and the order becomes 4.07 cubic yards and 5.78 tons, or 220 bags of 0.5 cu ft if you buy bagged stone.

The densities in the material list come from published bulk-density tables (Engineering ToolBox lists gravel at 105 lb/ft³ dry and 125 lb/ft³ wet, which is 1.42 to 1.69 short tons per cubic yard). Real stone varies with gradation, moisture and how it was loaded, so treat the default as a planning figure and replace it with the weight per yard your quarry or supplier quotes. Calculate each layer separately when a driveway has a base course and a top course.

Gravel volume, weight and bag formulas

  • Cubic feet = length (ft) x width (ft) x depth (in) / 12
  • Cubic yards = cubic feet / 27
  • Order cubic yards = cubic yards x (1 + allowance % / 100)
  • Short tons = order cubic yards x bulk density (short tons per yd³)
  • Bags = order cubic feet / bag size (cu ft), rounded up
  • Truckloads = order cubic yards / truck capacity (yd³), rounded up

Estimating Steps and Checks

1

Measure the area

Measure length and width in feet with a tape or wheel. For a circle (tree ring, fire pit) measure the diameter. For an L-shaped or curved driveway, split it into rectangles and triangles, run each one, and add the results.

2

Choose the depth

Use the depth from your plan or specification. Common planning depths are 2 inches for decorative beds and walkways, 3 inches for paths and patio surfaces, 4 inches for a driveway top course, and 6 inches or more for a base course or drainage. Measure depth in inches; the calculator converts to feet.

3

Pick the material and confirm its density

Select pea gravel, #57 crushed stone, crusher run, river rock or decomposed granite. The density field fills in automatically. If your supplier gives a weight per cubic yard, divide pounds by 2,000 and type that number in short tons per cubic yard instead.

4

Set the allowance, then read the order

Enter an allowance for settling, compaction, uneven subgrade and spillage, based on your own job history. Read the order volume and order weight, then round up to the supplier's delivery increment or to whole bags.

Common Checks

  • Units: depth is entered in inches. 4 inches is 0.333 ft. Multiplying square feet by 4 instead of 0.333 overstates the volume twelve times.
  • Coverage: one cubic yard covers 324 sq ft at 1 inch, 162 sq ft at 2 inches, 108 sq ft at 3 inches and 81 sq ft at 4 inches.
  • Weight follows density one for one. If the density you enter is 10 percent high, the tons are 10 percent high. Wet stone weighs more than dry stone (Engineering ToolBox: 125 vs 105 lb/ft³), which matters when you buy by the ton.
  • Layers: price a base course and a top course as two separate calculations. They usually use different stone, at different densities and prices.
  • Allowance is a multiplier applied once. A 10 percent allowance multiplies measured volume by 1.10. Do not add it again on top of the tons.

Gravel Calculator FAQs

How much gravel do I need for a driveway?

Multiply length x width x depth in feet and divide by 27. A 10 x 30 ft driveway at 4 inches is 300 x 0.333 = 100 cubic feet, or 3.70 cubic yards. A 12 x 50 ft driveway at 4 inches is 200 cubic feet, or 7.41 cubic yards. At 1.42 short tons per cubic yard (dry gravel) those are 5.25 and 10.5 short tons before any allowance. If the driveway has a base course under the top course, calculate each layer separately.

How many tons are in a cubic yard of gravel?

About 1.4 to 1.7 short tons. Engineering ToolBox lists gravel at 105 lb/ft³ dry and 125 lb/ft³ wet. A cubic yard is 27 cubic feet, so that is 2,835 to 3,375 lb, or 1.42 to 1.69 short tons. For crusher run, the closest published row is dry sand with gravel at 108 lb/ft³, or 1.46 short tons per cubic yard. Ask the supplier for the weight of the specific product, because they weigh every load.

How many cubic yards are in a ton of gravel?

Divide 1 by the density. At 1.42 short tons per cubic yard (dry), one ton is about 0.71 cubic yards, or 19 cubic feet. At 1.69 short tons per cubic yard (wet), one ton is about 0.59 cubic yards.

How deep should gravel be?

It depends on what the gravel does. Common planning depths are 2 inches for decorative beds and walkways, 3 inches for paths and patios, about 4 inches for a driveway top course, and 6 inches or more for a driveway base or a drainage trench. A new driveway over soft ground usually needs a compacted base course plus a top course, placed and compacted in lifts. Use the depth in your project specification when there is one.

How many bags of gravel are in a cubic yard?

A cubic yard is 27 cubic feet, so it takes 54 bags of 0.5 cu ft, or 27 bags of 1 cu ft. For the 10 x 30 ft driveway at 4 inches (100 cubic feet), that is 200 bags of 0.5 cu ft before allowance and 220 with 10 percent extra. At that size, bulk delivery is usually simpler than bags.

How much does a 0.5 cubic foot bag of gravel weigh?

At the published dry gravel density of 105 lb/ft³, half a cubic foot weighs about 52 lb. Wet stone at 125 lb/ft³ would weigh about 62 lb. Bag weights printed by the manufacturer are the figure to use when you plan by weight.

How much area does a ton of gravel cover?

At 105 lb/ft³ one short ton is about 19 cubic feet. That covers about 114 sq ft at 2 inches deep, 76 sq ft at 3 inches, or 57 sq ft at 4 inches, before any allowance. Denser or wetter stone covers less per ton.

Should I order extra gravel?

Usually yes, but set the amount from your own job history and the site: settling, compaction of a loose base, an uneven subgrade and spillage all use stone. The calculator multiplies measured volume by (1 + allowance). If you know the material loses 15 percent of its loose volume when compacted, divide the finished volume by 0.85 instead, which is the same as an allowance of about 17.6 percent. Apply the allowance once.

What is the best gravel for a driveway?

Most gravel driveways use an angular, well-graded base such as crusher run or road base, which compacts and locks together, with a top course of angular crushed stone such as #57. Round stone such as pea gravel and river rock rolls under tires, so it is better suited to paths, beds and drainage than to a driving surface.

Try it on your own plans

Automate your sitework takeoffs and quotes.

Get more sitework quotes out with less time measuring plans and moving quantities into a price sheet. BuildVision extracts site areas and measurements from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.

First takeoff free · No card · $299/seat/month after

Gravel Calculator | Cubic Yards, Tons, Bags & Cost