Construction Calculators

Jump to a tool or explore below.

Free Dirt Calculator

Dirt Calculator

Enter the area and depth to fill and get cubic yards, tons and truckloads of fill dirt, by soil type.

Fill Dirt Yards, Tons & Loads

Pick the soil type to fill in its density. Enter your hauler's truck capacity to plan loads.

Calculator inputs

Rectangle length, or triangle base.

Rectangle width, or triangle height.

Picking a material fills this in. Replace it with the supplier's figure when you have one.

Extra for settling, compaction, uneven ground and spillage. Set from job history.

Volume printed on the bag.

Ask the hauler. Heavy material can hit the weight limit before the box is full.

Planning estimate only. Confirm field measurements, product coverage, local requirements, waste, pricing, and supplier quantities before ordering or bidding.

Worked example: filling 20 x 20 ft, 6 inches deep

Loose moist dirt at the published 78 lb/ft³ (1.05 short tons per cubic yard), with a 15% allowance. These are the calculator defaults.

  1. 1Area = 20 ft x 20 ft = 400 sq ft
  2. 2Volume = 400 sq ft x (6 in / 12) = 200 cu ft
  3. 3Cubic yards = 200 / 27 = 7.41 yd³
  4. 4Order volume = 7.41 x 1.15 = 8.52 yd³
  5. 5Weight = 200 cu ft x 78 lb = 15,600 lb = 7.8 short tons measured, 8.97 to order
  6. 6Truckloads at 10 yd³ = 8.52 / 10 = 1 load (about 10.5 short tons when full)

Dirt and soil weight per cubic yard

These are the densities the material picker fills in. Each comes from the published row named in the last column. Moisture, gradation and how the material was loaded change real weight, so use your supplier's weight per yard when you have it.

Materiallb per cubic yardShort tons per yd³Tonnes per m³Typical usesPublished row
Dirt, loose and moist2,1061.051.25Fill dirt as usually deliveredDirt, loose moist: 78 lb/ft³
Dirt, loose and dry2,0521.031.22Screened fill and dry excavated soilDirt, loose dry: 76 lb/ft³
Topsoil / loam2,1601.081.28Lawns, garden beds, top dressingLoam: 80 lb/ft³
Clay, dry2,7001.351.60Clay fill, pond and berm coresClay, dry: 100 lb/ft³
Clay, wet2,9701.491.76Wet clay excavation and haul-offClay, wet: 110 lb/ft³

Source: Engineering ToolBox, Dirt and Mud - Densities. Where the source gives a range, the default is its midpoint. Short tons per cubic yard = lb/ft³ x 27 / 2,000.

Fill depths and coverage

The depth presets in the calculator, and how far one cubic yard goes at each depth. Use the depth in your plan or specification when there is one.

DepthCommon use1 yd³ coversYards per 100 sq ft
3 in (7.6 cm)low spots, grading108 sq ft0.93 yd³
6 in (15.2 cm)fill and re-grade54 sq ft1.85 yd³
12 in (30.5 cm)raised area, backfill27 sq ft3.70 yd³
18 in (45.7 cm)-18 sq ft5.56 yd³
24 in (61.0 cm)-14 sq ft7.41 yd³

Automate your sitework takeoffs and quotes.

Get more sitework quotes out with less time measuring plans and moving quantities into a price sheet. BuildVision extracts site areas and measurements from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.

How the Dirt Calculator Works

Fill dirt is ordered by the cubic yard and hauled by the truckload, and the truck is limited by weight as well as volume. This calculator works out the volume from the area and depth, adds your allowance, and converts to weight using the soil type you choose.

Filling a 20 x 20 ft area 6 inches deep takes 200 cubic feet, or 7.41 cubic yards. At the published density for loose moist dirt (78 lb/ft³) that is 15,600 lb, or 7.8 short tons. With a 15 percent allowance the order is 8.52 cubic yards and about 9 tons.

Densities come from Engineering ToolBox: loose dry dirt 76 lb/ft³, loose moist dirt 78, loam 80, dry clay 100, wet clay 110. They describe loose material. Dirt that will be compacted in place needs more loose volume than the finished hole or grade; set the allowance from your soils report or job history, not from a single rule of thumb.

Dirt volume and weight formulas

  • Cubic feet = length (ft) x width (ft) x depth (in) / 12
  • Cubic yards = cubic feet / 27
  • Order cubic yards = cubic yards x (1 + allowance % / 100)
  • Short tons = order cubic yards x bulk density (short tons per yd³)
  • Truckloads = order cubic yards / truck capacity (yd³), rounded up

Estimating Steps and Checks

1

Measure the area to fill

Measure length and width in feet. For a round hole or pond, use Circle and measure the diameter. For a long trench, enter its length and width and the trench depth in inches.

2

Find the average depth

Fill is rarely an even depth. Take depth readings across the area with a string line or level and average them. Split the area if one end is much deeper than the other.

3

Choose the soil type

Pick loose moist dirt, loose dry dirt, loam or clay. The density fills in from the published table. If the supplier quotes a weight per yard, enter that instead.

4

Set the allowance and plan loads

Add an allowance for compaction and settling, then enter your hauler's truck capacity. The result shows how many loads it takes and roughly what a full load weighs, so you can check it against the truck's payload.

Common Checks

  • A hole 3 ft x 3 ft x 3 ft is exactly 1 cubic yard. Use it as a quick sense check on bigger numbers.
  • Depth is in inches: 36 inches for a 3 ft deep trench. Entering 3 gives one twelfth of the volume.
  • Weight check: at 78 lb/ft³, one cubic yard of loose moist dirt is 2,106 lb, so 10 cubic yards is about 10.5 short tons.
  • Clay is heavier than loam (Engineering ToolBox: 100 to 110 vs 80 lb/ft³). Choose the right soil before planning loads by weight.

Dirt Calculator FAQs

How much dirt do I need?

Multiply length x width x depth, all in feet, and divide by 27 for cubic yards. Filling a 20 x 20 ft area 6 inches deep is 400 x 0.5 = 200 cubic feet, or 7.41 cubic yards. Add an allowance if the fill will be compacted.

How much does a cubic yard of dirt weigh?

Using Engineering ToolBox densities: loose dry dirt 76 lb/ft³ is about 2,052 lb per cubic yard (1.03 short tons), loose moist dirt 78 lb/ft³ is about 2,106 lb (1.05 tons), and wet clay 110 lb/ft³ is about 2,970 lb (1.49 tons). Moisture makes a big difference.

How many cubic yards of dirt are in a ton?

About 0.95 cubic yards per short ton for loose moist dirt (1 / 1.053), and about 0.67 cubic yards per ton for wet clay (1 / 1.485).

How do I calculate dirt for a hole or trench?

Length x width x depth in feet, divided by 27. A trench 50 ft long, 2 ft wide and 3 ft deep is 300 cubic feet, or 11.1 cubic yards. Enter the depth as 36 inches.

How many truckloads of dirt will I need?

Divide the order volume by the truck's capacity and round up. Check weight too: a 10 cubic yard load of loose moist dirt weighs about 10.5 short tons at 78 lb/ft³, and the truck's legal payload may be the limit before the box is full. Ask the hauler what their trucks carry.

Do I need extra dirt for compaction?

Yes, when the fill is compacted. Loose dirt takes up more space than the same dirt compacted in place, so order more loose volume than the finished grade needs. The right allowance depends on the soil and the compaction required; use your soils report, the supplier or your own job history.

What is the difference between fill dirt and topsoil?

Fill dirt is subsoil used to raise grade, backfill and level, and it is usually compacted. Topsoil is the organic upper layer used where plants or grass will grow. Use the Topsoil Calculator for lawns and beds.

Try it on your own plans

Automate your sitework takeoffs and quotes.

Get more sitework quotes out with less time measuring plans and moving quantities into a price sheet. BuildVision extracts site areas and measurements from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.

First takeoff free · No card · $299/seat/month after

Dirt Calculator | Cubic Yards, Tons & Truckloads