Construction Calculators

Jump to a tool or explore below.

Free Roofing Square Calculator

Roofing Square Calculator

One roofing square is 100 sq ft of roof surface. Enter a footprint or a sloped roof area, the pitch, and waste, and get squares and whole shingle bundles to order.

Square feet to squares
Pitch multiplier
Whole bundles

Roofing Squares Calculator

Pick footprint if you measured on the ground or from plans; pick sloped roof surface if the area came from an aerial report

Calculator inputs

Enter 6 for a 6/12 roof. Ignored for sloped roof surface.

About 10% on a simple gable, 15% with hips and valleys, 20% on cut-up roofs.

Planning estimate only. Confirm field measurements, product coverage, local requirements, waste, pricing, and supplier quantities before ordering or bidding.

What Is a Roofing Square?

A roofing square is a unit of roof surface equal to 100 square feet, the area of a 10 × 10 ft patch of roof (9.29 m²). It is measured on the slope. A roof is described in squares because shingles are packaged and priced that way: most 3-tab and architectural shingles come 3 bundles to the square, so a 25-square roof is 75 bundles before waste.

The two numbers people confuse are the footprint and the roof area. The footprint is the flat outline seen from above. The roof area is larger by the pitch multiplier, sqrt(1 + (rise / 12)²): 5.4% larger at 4/12, 11.8% at 6/12, 20.2% at 8/12, and 41.4% at 12/12. Squares always come from roof area.

Worked Example

Inputs: 1,800 sq ft footprint to the drip edge, 6/12 pitch, 10% waste, 3 bundles per square.

Roof area: 1,800 × 1.118 = 2,012 sq ft, which is 20.12 squares.

With waste: 20.12 × 1.10 = 22.14 squares.

Bundles: 22.14 × 3 = 66.4, rounded up to 67 bundles (22.33 squares of shingles).

Need starter, ridge cap, and nails too? Carry the roof area into the shingle calculator.

Roofing Squares by Pitch

Squares of roof for every 1,000 sq ft of footprint, before waste. Multiply by your footprint in thousands. For the angle of each pitch, use the roof pitch calculator.

PitchMultiplierSquares per 1,000 sq ft footprint
2/121.01410.14
3/121.03110.31
4/121.05410.54
5/121.08310.83
6/121.11811.18
7/121.15811.58
8/121.20212.02
9/121.25012.50
10/121.30213.02
12/121.41414.14

How Many Squares Is My Roof?

Squares before waste for common footprints (measured to the drip edge) at three common pitches. Living area is not footprint: a two-story house has a much smaller roof outline than its square footage.

Footprint (sq ft)4/126/128/12
1,20012.613.414.4
1,50015.816.818.0
2,00021.122.424.0
2,50026.428.030.0
3,00031.633.536.1
Bundles per square: GAF lists Royal Sovereign 3-tab and Timberline HDZ architectural shingles at 33.33 sq ft per bundle, 3 bundles per square. Owens Corning lists Duration Premium at 4 bundles per square. Set the bundles-per-square field to match the product you are buying.

Automate your roofing takeoffs and quotes.

Get more roof quotes out with less time measuring plans and converting areas to squares by hand. BuildVision extracts roof areas and lengths from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.

How the Roofing Square Calculator Works

A roofing square is 100 square feet of roof surface (9.29 square meters). Roofers price labor, order shingles, and compare measurement reports in squares, so the first number on any shingle job is how many squares the roof is. This calculator converts either a footprint you measured from the plans or the ground, or a sloped roof area from an aerial report, into squares, adds waste, and rounds up to whole bundles.

Worked example: a house with an 1,800 sq ft footprint (measured to the drip edge) under a 6/12 roof. The pitch multiplier is sqrt(1 + (6/12)^2) = 1.118, so the roof is 1,800 x 1.118 = 2,012 sq ft, or 20.12 squares. With 10 percent waste that is 22.14 squares. At 3 bundles per square the order is 22.14 x 3 = 66.4, rounded up to 67 bundles, which is 22.33 squares of shingles.

If your number already is sloped roof surface, from an aerial measurement report or from adding up each roof plane, choose Sloped roof surface and the pitch is not applied again. Applying the multiplier twice is one of the easiest ways to over-order.

Roofing square formulas

  • 1 roofing square = 100 sq ft = 9.290304 m² of roof surface
  • Pitch multiplier = sqrt(1 + (rise / 12)^2)
  • Roof area = footprint x pitch multiplier
  • Squares = roof area (sq ft) / 100
  • Squares with waste = squares x (1 + waste % / 100)
  • Bundles = ceil(squares with waste x bundles per square)

Estimating Steps and Checks

1

Decide what area you have

A footprint or plan area is horizontal: it comes from the plans, a tape around the house, or a property record. A sloped roof area is measured along the roof planes: it comes from an aerial report or plane-by-plane measurements. Pick the matching option so the pitch is applied once.

2

Measure the footprint to the drip edge

Include the overhangs. Take the outside dimensions of the roof outline, not the walls. Break L-shaped and T-shaped houses into rectangles, add their areas, and enter the total.

3

Enter the pitch

Enter the rise per 12 inches of run, such as 6 for a 6/12 roof. If you do not know it, measure it with the roof pitch calculator. Roofs with planes at different pitches should be run plane by plane.

4

Add waste and round to bundles

Use about 10 percent waste for a simple gable, 15 percent with hips and valleys, and 20 percent for cut-up roofs. Then round up to whole bundles; most 3-tab and architectural shingles are 3 bundles per square.

Common Checks

  • Definition check: a square is always 100 sq ft of roof surface, whatever the shingle. Bundles per square is what changes between products.
  • Pitch check: the multiplier is 1.054 at 4/12, 1.118 at 6/12, 1.202 at 8/12, and 1.414 at 12/12. Skipping it on a 12/12 roof under-orders by 29 percent of what is needed.
  • Double-count check: aerial measurement reports already give sloped area in squares. Do not multiply those by the pitch again.
  • Rounding check: shingles are sold by the bundle, so round bundles up, not squares. 22.14 squares at 3 bundles per square is 67 bundles, not 69.

Roofing Square Calculator FAQs

What is a square in roofing?

A roofing square is 100 square feet of roof surface, the area of a 10 x 10 ft section. It is measured on the slope, not on the ground, and it is the unit roofers use to order shingles and price labor.

How many squares is my roof?

Multiply the footprint (measured to the drip edge) by the pitch multiplier and divide by 100. A 1,500 sq ft footprint at 5/12 is 1,500 x 1.083 = 1,625 sq ft of roof, or 16.25 squares before waste.

How do I convert square feet to roofing squares?

Divide the sloped roof area in square feet by 100. 2,350 sq ft of roof is 23.5 squares. If you only have the house footprint, multiply it by the pitch multiplier first.

How many bundles are in a square of shingles?

Most 3-tab and architectural shingles are 3 bundles per square. GAF lists Royal Sovereign and Timberline HDZ at 33.33 sq ft per bundle, 3 bundles per square. Some heavy designer lines are 4 bundles per square; Owens Corning lists Duration Premium at 4. Check the wrapper.

How many squares is a 2,000 sq ft house?

It depends on the pitch and the overhangs. A 2,000 sq ft single-story footprint at 4/12 is 21.1 squares, at 6/12 is 22.4 squares, and at 8/12 is 24 squares, before waste. A two-story house with 2,000 sq ft of living space has a much smaller footprint, so measure the roof outline rather than using living area.

How much waste should I add to roofing squares?

A common planning range is 10 percent for a simple gable, 15 percent with hips and valleys, and 20 percent for complex roofs. Waste comes from cuts at hips, valleys, and rakes, and from starter and cap if you cut them from field shingles.

How many square meters is a roofing square?

One roofing square is 100 sq ft, which is 9.29 m². To convert a metric roof area to squares, divide the area in square meters by 9.29. A 200 m² roof is 21.5 squares.

Does a roofing square include the overhang?

Squares count every square foot of roof surface, including overhangs. Measure the footprint to the drip edge, not to the outside of the walls, or the order will come up short.

Try it on your own plans

Automate your roofing takeoffs and quotes.

Get more roof quotes out with less time measuring plans and converting areas to squares by hand. BuildVision extracts roof areas and lengths from your plans and carries them through your rates and assemblies into a branded quote. Your team checks the quantities and pricing before sending. Try it free on your own plans.

First takeoff free · No card · $299/seat/month after

Roofing Square Calculator | Squares, Bundles by Pitch