In construction estimating

P-Trap

A U-shaped section of drain pipe below a fixture that holds a water seal to block sewer gas from entering the building while letting wastewater drain.

Definition

A P-trap is the U-shaped bend of pipe installed in the drain line directly below a plumbing fixture such as a sink, lavatory, tub, or shower. The bend always holds a small amount of water, called the trap seal, which stops sewer gases from coming back up through the drain while still letting wastewater flow out. The name comes from its shape: the U-bend plus the horizontal trap arm that runs to the wall look like a sideways letter P.

Model plumbing codes require every fixture to be trapped, and most require a trap seal depth between 2 and 4 inches. The trap only works if it is vented, because an unvented trap can be siphoned dry when water rushes through the line. S-traps, which drop straight down into the floor without a vented trap arm, are prohibited by modern codes for that reason. Toilets have a trap built into the bowl, so they do not get a separate P-trap.

How p-trap is used in estimating

P-traps rarely appear as their own symbol on plumbing drawings. They are implied by the fixture schedule, which lists each fixture with its trap size, waste size, and vent size, and by the plumbing specifications that describe trap material and finish, such as chrome-plated brass at exposed lavatories or PVC and ABS at concealed locations. Common minimum trap sizes are 1-1/4 inch for lavatories, 1-1/2 inch for kitchen sinks and bathtubs, and 2 inch for showers.

In a takeoff, P-traps are counted as each (EA), grouped by size and material. They are frequently carried inside a fixture assembly along with the tailpiece, stop valves, and supplies rather than priced as a separate line. Watch for fixtures where the trap is furnished by the fixture manufacturer or by another trade, ADA lavatories that need insulated or offset traps, and floor drains, which also require a trap.

How to count P-traps in a plumbing takeoff

Count fixtures from the floor plans and reconcile them against the fixture schedule, then assign a trap to every fixture that does not have an integral trap, including floor drains, floor sinks, mop sinks, and equipment drains. Separate exposed decorative traps from concealed traps, because finish and material drive cost. Confirm in the specification whether trap primers are required on floor drains, since those add valves and piping that are easy to miss. A fixture-based assembly keeps traps from being dropped when quantities change after an addendum.

Frequently asked questions

Q.Why is it called a P-trap?

The U-shaped bend combined with the horizontal arm that connects to the drain in the wall resembles the letter P lying on its side. The design traps water in the bend, which is where the word trap comes from.

Q.What is the difference between a P-trap and an S-trap?

A P-trap exits horizontally into a wall drain that connects to a vent, so the water seal stays in place. An S-trap turns back down into the floor, which can siphon the seal out of the trap and let sewer gas in. Current model plumbing codes do not allow new S-traps.

Q.What size P-trap do I need?

Trap size depends on the fixture and the plumbing code. Typical minimums are 1-1/4 inch for a bathroom lavatory, 1-1/2 inch for a kitchen sink or bathtub, and 2 inch for a shower. The fixture schedule on the plumbing drawings states the required size for each fixture on a commercial project.

Q.Does a toilet have a P-trap?

Not a separate one. A toilet has an integral trap molded into the porcelain, so no additional P-trap is installed below it. That is why toilets are excluded when estimators count traps.

BuildVision AI

Save time with AI-powered estimating

Producing accurate p-trap the manual way takes hours. BuildVision AI reads your drawings and generates structured takeoffs and BOQs in minutes, ready for your own pricing.

AI takeoffs

Direct from PDF plans, uploaded as one PDF or a ZIP of PDFs.

BOQ generation

Itemized bills of quantities ready for pricing or owner submission.

Quote and bid

Branded quotes priced with your own rates, shared as a link.

First takeoff free · No card · $299/seat/month after

P-Trap: What It Is and How It Works | Glossary